Best ASIC Miner

ASIC Antminer R4 | Best Bitcoin Mining Hardware !

Best bitcoin mining hardware, ASIC Antminer : Why Antminer R4 can be a much better choice than many other Bitcoin miners?

So what makes it best bitcoin mining hardware : It is much more quiet than the original older miner and maintains the speed of 8 TH/s. Discussion about the new design of the fan as well as the custom design. So, as it is exhausted it will not be easy to replace.

Best ASIC Miner

Best ASIC Miner

On the other hand, since it runs at a low speed, I hope it will increase its durability. The clock rate can not be specified in R4 software. Unlike the old ones that can be quickly lit up in good condition.

The program takes about 2 minutes and returns to error until it is ready. Sometimes R4 hash rates drops than 50%, but a reboot will fix this all.


Technical Specifications

Hash Rate:  8TH/s & 8.7TH/s (Batch 3 and Batch 4). Variation of ± Five % is expected.

Maximum Power Consumption: 845 W +Nine% (at the wall, with Bitmain’s APW5 PSU,93% efficiency, 25°C ambient temp)

Power Efficiency:  0.1 J/GHs +Nine% on the wall (with Bitmain’s APW5 PSU, 93% efficiency, ambient temperature 25°C )

Noise:  52dB (at a test distance of 1M from the air outlet and at ambient temp of 30°C in a silent room)

DC Voltage Input:  11.60 ~13.00V

Frequency:  Set Automatically.

Chip quantity per unit:  126 chips (16nm BM1387 ASIC chip)

Network Connection: Ethernet

Operation Temperature Range:  10°C to 40°C.

Operation Humidity Range: 5%RH-95%RH, prevent condensation.

Storage Temperature Range: -40°C to 85°C

Product size: 515mm (L) x 100mm (W) x 222mm (H)

Package size: 610mm (L) x 215mm (W) x 340mm (H)

Package weight: 9 kg

Gains and Profits with Best hardware

With profits as the primary purpose of the mining, every equipment is judged on the basis of its productivity. For Antminer R4, it is the same.

If you invest $ 1,000 to buy the unit and invest another $ 500 for the PSU, it takes about 500 days to get the investment back.

Asic Mining Hardware | Innovative Technology

With the execution of the Bitmain’s BM1387 chip that uses the TSMC’s 16nm FinFET innovation, the R4 provides an exceptional 0.098 J/GHs productivity.

Every one of the Antminer R4 has 126 of the chips to create high effectiveness and hash rate of 8.5TH/s.

The Antminer R4 likewise has a control board that utilizes Dual-center Arm Cortex-A9 that depends on the Application Processor Unit.

The control board on the R4 uses the Xilinx’s ZYNQ-7000 framework that speeds up the mining procedure just as transmission of the mined block.

Asic Hardware | Design

Unlike other hardware miners, R4 reduces the noise generated during extraction, even at maximum speed.

It uses a rotating blade system instead of conventional fans, which, frankly, do not go in the positive direction of most miners.

The silent-split air conditioner can be inspired with less than half of the noisy standard fan. In addition, the fan is automatically controlled, that is, it never creates noise unnecessarily.

With new innovative fans, the R4 operates in a temperature range of 10 to 40 degrees Celsius.

Power Consumption & Setting Up | Efficiency

With a hash rate of 8.6 TH/s, the R4 has a power consumption of 845 watts.

To set up the R4 miner, the miner could register on the Bitmain site and follow the rules. They would get the IP address of the miner.

First set up the control panel page before the mining.Like the S9, the Antminer R4 has a productivity of 0.098 J/GHs.

This productivity is accomplished by the FinFET technology used in Bitmain BM1387 chips. In this way the R4 accomplishes the efficiency through using 126 nos. of the chips.

The R4 user interface, which is very similar to most Bitmain device interfaces, was built into the baseplate.

This is very easy to use. If the miner is configured, it can contain the address of its wallet and pool settings. It is also possible to easily adjust the fan speed.

Cost | Antminer

R4 Typically, Antminer R4 expects about $ 1,600 which makes it best ASIC Miner to try out with comparably low cost. It’s cheaper than S9 and S7.

The R4 is surprised to find new quiet fans increasingly aiming to reduce the mid-range turbulence (which was the weight of the mining crew).

It controls productivity and is less expensive than other standard bitmain devices.

Most likely, in the market for standard mining equipment, there is not yet a large spending plan, and then R4 can be a decent launch site.

CHECK HERE |….BEST GPU FOR MINING….|

Add a Comment

Your email address will not be published. Required fields are marked *